tree felling techniques chainsaw

Certified arborist Mark Chisholm provides helpful and important safety tips for professionals on how to fell a tree with a chainsawWatch all the Pro Tips vi. The face cut sometimes called a notch cut comes first.

Pin On Chainsaws

First of all make the forward-facing notch point toward the desired fall.

. Tree is small enough for the saw bar to reach through the tree in one cut. How to cut down or fell a tree using a chainsaw safely. Saw a horizontal felling cut a few inches above the undercut level on the opposite side of the trunk to create a hinge on which the tree will fall in a measured way.

Pavel will work with the group to go over basic use with an emphasis on safety and control. The top cut the pluge cut and the back or felling cut. This cut is accomplished by cutting up through the underside of the log or branch thats sitting horizontally.

This involves making a cut into the tree using the tip of the chainsaws bar. Take a look at How to make a felling cut to view different types of felling cuts. We have partnered with experienced woods worker forester and arborist Pavel McGlave who is a certified SAWW Safety and Woods Worker trainer.

Its a potentially dangerous job thats best left to trained professionals. How to Fell a Tree. With advice from our STIHL experts as well as professional arborist and.

Remember to saw right to the hinge width. A bore can be used with most felling methods and can be applied regardless of guide bar length and tree size. A final horizontal back-cut is made below the boring cut.

THIS IS A VERY PROFESSIONAL TYPE OF FELLING. Watch the following video to learn how to cut down. Choose Where to Cut.

To make the hinge effective ensure it is 10 of the tree trunk diameter. Felling The Tree Summarize Mark Cut Locations With Surveyors Paint Visually Plan Felling Approach Face The Tree Two Planar Cuts Select A Face Cut Type. The technique used for making the felling cut depends on the thickness of the trunk and the length of the guide bar.

This notch should open at 70 degrees for maximum control of the tree direction and minimize the compression force on the wedge. Fir tree was lying across a steep slope. However if the tree is a manageable size you may choose to tackle the job yourself.

The safe felling of a tree using an open face notch consists of making three precise and strategic cuts. Run the saw at full throttle as it cuts into the limb. For your tree to have a smooth fall you will make a V-shaped notch on the side of the tree thats facing the direction where you want it to fall.

To fell a tree with a chainsaw you will need to make three cuts two on the face and one on the back. Cutting down a tree also known as felling a tree requires careful planning and a high degree of skill. Dont cut with the chain saw above shoulder height.

Limbing is the process of using a chainsaw to remove limbs from a tree that has fallen over or is lying on the ground. Pull the saw across the trunk and support the saw against your right leg. We recommend using the Safe corner.

BORING TECHNIQUES HEAVY LEANERS CAUTION. The guide bar will then be in the correct position for removing the limbs on top. The felling cut will normally be level with or slightly above the level of the directional notch.

Using full throttle move the saw forward using your. Cutting down a tree also known as felling a tree requires careful planning and a high degree of skill. About 30 feet from the roots the tree was balanced on a small stump.

Small trees can be limbed while they are standing. Open Conventional Humboldt Always Located On The Desired Felling Direction Side Of The Tree Check Face Location With A Horizontal Line Centered And. When slashing felling small trees cut the stumps as close to the ground as possible without hitting the dirt with your chain.

It must be made on the side of the tree that faces the. Chapter 3Chain Saw Tasks and Techniques The following example shows the importance of following proper pro-cedures when bucking blowdown. Felling wedges can then be used during the final cut to assist the tree in beginning to fall.

Always start boring with the lower part of the bar tip. When it comes to tree removal by using a chainsaw preparation is key. Make the Face Notch.

The hold-ing wood at the back severs and the tree falls guided by the hinge. Stumps are cut low so they will not be as noticeable and will present fewer hazards for people and wildlife. This V-shaped cut should reach the center of the tree and the tips of the top and bottom cut must meet in the middle.

Cut at about the knee height of a regular-sized person. In this two day class each student will be introduced to the chainsaw and all of its basic parts and controls. The butt end was still anchored by a few roots.

Also use the standard notch size of about 13 of the trees diameter. You can find more information about on httpwwweuropeanchainsaweu and. Your STIHL chainsaw can be a powerful tool capable of taking down whole trees.

But before tackling the daunting task of felling a tree make sure you are taking all the necessary precautions to maximize your safety and following the best practices to effectively bring down a tree. Felling The Tree Summarize Mark Cut Locations With Surveyors Paint Visually Plan Felling Approach Face The Tree Two Planar Cuts Select A Face Cut Type. This video is the exam preperation for the European Chainsaw Certificate level 2.

To be able to perform the safe corner method and turn around method you need to master bore cutting.

Pin On Chainsaw Stuff